Actions

Difference between revisions of "The Art of Sword Forging"

From Londonhua WIKI

(Time Period)
 
(24 intermediate revisions by one other user not shown)
Line 6: Line 6:
 
|bodystyle  = width:25em
 
|bodystyle  = width:25em
 
|image = [[File:Cool Sword pic.JPG|x450px|alt=Cool Sword Pic]]
 
|image = [[File:Cool Sword pic.JPG|x450px|alt=Cool Sword Pic]]
|caption = Deliverable Sword by Tower Hill
+
|caption = Deliverable Sword
 +
|label2 = '''Location'''
 +
|data2 = Forge of Avalon, Glastonbury
 
}}
 
}}
<nowiki>__TOC__</nowiki>.
 
  
 
__TOC__
 
__TOC__
  
 
=Abstract=
 
=Abstract=
The purpose of this project was to study how art was involved in medieval sword making and create a medieval sword. I have never done any kind of forging previously. I found that most art in medieval swords are religious in nature and meant to give the wielder divine favor in battle. A lot is not known about inscriptions because of a lack of understanding in Latin abbreviations and grammar. Sword blades could also be decorated with wave patterns during forging. I created a sword in order to understand the processes that would have been involved in creating the art. I was unable to actually create ant art in my sword due to a lack of skill.  
+
The purpose of this project was to study how art was involved in medieval sword making and create a medieval sword. I have never done any kind of forging previously. I found that most art in medieval swords are religious in nature and meant to give the wielder divine favor in battle. A lot is not known about inscriptions because of a lack of understanding in Latin abbreviations and grammar. Sword blades could also be decorated with wave patterns during forging. I created a sword in order to understand the processes that would have been involved in creating the art. I was unable to actually create any art in my sword due to a lack of skill.  
  
 
<br><br>
 
<br><br>
Line 25: Line 26:
 
==Time Period==
 
==Time Period==
 
<br>
 
<br>
I am defining a Medieval sword to mean any sword crafted in Europe between 500 and 1400 AD. During this time period swords would be mainly used for fighting as seen by the fact that the shape of the blade depends on the fighting style native to that area. They also would have be used in the Crusades.<ref>Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.</ref> The majority of swords where made to be functional as opposed to be artistic. The swords did have art on them designed to be functional in the forms of engravings meant to give the blades magical power or blessings from various deities.<ref>Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132</ref> Designs in the blades did come about from trying to mimic Damascus steel, steel made from wootz, an iron ore from India, and crafted in Damascus, a trade center from that time period, because of its highly functional qualities.<ref>Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.</ref>
+
I am defining a Medieval sword to mean any sword crafted in Europe between 500 and 1400 AD. During this time period, swords would be mainly used for fighting as seen by the fact that the shape of the blade depends on the fighting style native to that area. They also would have be used in the Crusades.<ref>Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.</ref> The majority of swords where made to be functional as opposed to be artistic. The swords did have art on them designed to be functional in the forms of engravings meant to give the blades magical power or blessings from various deities.<ref>Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132</ref> Designs in the blades did come about from trying to mimic Damascus steel, steel made from wootz, an iron ore from India, and crafted in Damascus, a trade center from that time period, because of its highly functional qualities.<ref>Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.</ref> For the most part the swords were not very decorated.
 
<br><br>
 
<br><br>
  
Line 31: Line 32:
 
<br>
 
<br>
 
===Blade Patterns===
 
===Blade Patterns===
 +
{{Infobox
 +
|title = Damascus Steel Knife
 +
|bodystyle = width:25em
 +
|image = [[File:Damascus steel hunting knife (4121913093).jpg|320px|alt=Image ]]
 +
|caption = Damascus Steel has a distinctive wave pattern
 +
|label2 = '''Artist'''
 +
|data2 = Attributed to Rich Bowen<ref> Attributed to Rich Bowen from Lexington, KY, USA (Damascus steel hunting knife) [CC BY 2.0 (http://creativecommons.org/licenses/by/2.0)], via Wikimedia Commons</ref>
 +
}}
 
<br>
 
<br>
[[File: Damascus steel hunting knife (4121913093).jpg|x320px|thumb| Attributed to Rich Bowen from Lexington, KY, USA (Damascus steel hunting knife) [CC BY 2.0 (http://creativecommons.org/licenses/by/2.0)], via Wikimedia Commons]]<br>
+
Damascus steel swords were very popular during the medieval period due to their combination of strength and flexibility. Using Damascus steel causes a water ripple looking pattern in the blade. For this reason, many smiths found ways to copy the pattern despite not having the steel. The patterning was entirely for aesthetic uses and had no real meaning beyond the implication that it was a high quality sword which may or may not have been true depending on whether or not it was Damascus steel and if it was forged properly.<ref>Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.</ref><br><br>
Damascus steel swords were very popular during the medieval period due to there combination of strength and flexibility. Using Damascus steel causes a water ripple looking pattern in the blade. For this reason many smiths found ways to copy the pattern despite not having the steel. The patterning was entirely for aesthetic uses and had no real meaning beyond the implication that it was a high quality sword which may or may not have been true depending on whether or not it was Damascus steel and if it was forged properly.<ref>Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.</ref><br><br>
 
  
 
===Inscriptions===
 
===Inscriptions===
 +
{{Infobox
 +
|title = Blade with Inscriptions
 +
|bodystyle = width:25em
 +
|image = [[File:Cawood sword - blade with inscription - YORYM 2007 3086.JPG|320px|alt=Image ]]
 +
|caption = The meaning of many inscriptions are unknown
 +
|label2 = '''Artist'''
 +
|data2 = Photographed by: York Museums Trust Staff<ref>Photographed by: York Museums Trust Staff [CC BY-SA 4.0 (http://creativecommons.org/licenses/by-sa/4.0)], via Wikimedia Commons</ref>
 +
}}
 
<br>
 
<br>
[[File:Cawood sword - blade with inscription - YORYM 2007 3086.JPG|x320px|thumb|By Photographed by: York Museums Trust Staff [CC BY-SA 4.0 (http://creativecommons.org/licenses/by-sa/4.0)], via Wikimedia Commons]]<br>
 
 
Inscriptions on Medieval swords are very common and severed a variety of purposes. There are four kinds of inscriptions that are found on medieval swords, runic inscriptions, symbols, religious vocations, and periodic sequences.<ref>Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132</ref> Runic inscriptions were frequently maker's marks, which show who forged the sword, but also could have been the names of the owners, makers (their name being different form their mark), donators, carriers or the weapons name. Having a name was rare and was likely used for gifting swords. They could have also been to remind the barer to show bravery or been written by sorceresses to give the blade magic power.<ref>Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132</ref><ref>Nickel, H. (1969). A Knightly Sword with Presentation Inscriptions. Metropolitan Museum Journal, 2, 209-210. doi:10.2307/1512593</ref> Religious vocations would have been meant to give the wielders divine favor in battle.<ref>Nickel, H. (1969). A Knightly Sword with Presentation Inscriptions. Metropolitan Museum Journal, 2, 209-210. doi:10.2307/1512593</ref> Symbols and ornaments were likely religious.<ref>Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132</ref>  Most writing on medieval swords have religious, magical, or other protective meaning.<ref>Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132</ref><ref>Nickel, H. (1969). A Knightly Sword with Presentation Inscriptions. Metropolitan Museum Journal, 2, 209-210. doi:10.2307/1512593</ref> Among more common letter sequences such as SDX, which means Sanctus Dominus Christus or Holy Lord Christ, SD(I)X, which could have meant salvator Dominus Iesus Xrist or Liberator Lord Jesus Christ, and ULFBERTH which were mass produced. There are different sequences that do not appear to have any meaning.<ref>Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132</ref>  This could be because hey are Latin abbreviations of songs or verse that are unknown or due to a lack of understanding the grammar. Because witting was very uncommon at the time, any kind of lettering would have a magical connotation. Some of the inscriptions could have been nonsense meant to be a magical language.<ref>Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132</ref>  
 
Inscriptions on Medieval swords are very common and severed a variety of purposes. There are four kinds of inscriptions that are found on medieval swords, runic inscriptions, symbols, religious vocations, and periodic sequences.<ref>Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132</ref> Runic inscriptions were frequently maker's marks, which show who forged the sword, but also could have been the names of the owners, makers (their name being different form their mark), donators, carriers or the weapons name. Having a name was rare and was likely used for gifting swords. They could have also been to remind the barer to show bravery or been written by sorceresses to give the blade magic power.<ref>Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132</ref><ref>Nickel, H. (1969). A Knightly Sword with Presentation Inscriptions. Metropolitan Museum Journal, 2, 209-210. doi:10.2307/1512593</ref> Religious vocations would have been meant to give the wielders divine favor in battle.<ref>Nickel, H. (1969). A Knightly Sword with Presentation Inscriptions. Metropolitan Museum Journal, 2, 209-210. doi:10.2307/1512593</ref> Symbols and ornaments were likely religious.<ref>Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132</ref>  Most writing on medieval swords have religious, magical, or other protective meaning.<ref>Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132</ref><ref>Nickel, H. (1969). A Knightly Sword with Presentation Inscriptions. Metropolitan Museum Journal, 2, 209-210. doi:10.2307/1512593</ref> Among more common letter sequences such as SDX, which means Sanctus Dominus Christus or Holy Lord Christ, SD(I)X, which could have meant salvator Dominus Iesus Xrist or Liberator Lord Jesus Christ, and ULFBERTH which were mass produced. There are different sequences that do not appear to have any meaning.<ref>Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132</ref>  This could be because hey are Latin abbreviations of songs or verse that are unknown or due to a lack of understanding the grammar. Because witting was very uncommon at the time, any kind of lettering would have a magical connotation. Some of the inscriptions could have been nonsense meant to be a magical language.<ref>Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132</ref>  
 +
<br>
 +
====Metropolitan Museum of Art's c.1400 Sword====
 +
This is one of the very few cases where the inscription on a sword is not a religious invocation. The script on the pommel reads "here, too virtue has its due reward" and the script on the blade is mostly illegible. It could be the only surviving sword with a presentation inscription from the 14th century.<ref>Nickel, H. (1969). A Knightly Sword with Presentation Inscriptions. Metropolitan Museum Journal, 2, 209-210. doi:10.2307/1512593</ref>
 +
<gallery mode="packed">
 +
Image:Metropolitan Museum's Sword.PNG|''The Sword<ref>Nickel, H. (1969). A Knightly Sword with Presentation Inscriptions. Metropolitan Museum Journal, 2, 209-210. doi:10.2307/1512593</ref>''
 +
Image:Metropolitan Museum Pommel.PNG|''The Pommel with Inscriptions<ref>Nickel, H. (1969). A Knightly Sword with Presentation Inscriptions. Metropolitan Museum Journal, 2, 209-210. doi:10.2307/1512593</ref>''
 +
Image:Metropolitan Museum Maker's Mark.PNG|''Maker's Mark on the Sword<ref>Nickel, H. (1969). A Knightly Sword with Presentation Inscriptions. Metropolitan Museum Journal, 2, 209-210. doi:10.2307/1512593</ref>''
 +
Image:Metropolitan Museum Blade Inscription.PNG|''Mostly illegible blade Inscription<ref>Nickel, H. (1969). A Knightly Sword with Presentation Inscriptions. Metropolitan Museum Journal, 2, 209-210. doi:10.2307/1512593</ref>''
 +
</gallery>
 
<br><br>
 
<br><br>
  
Line 45: Line 69:
 
===Blade Patterns===
 
===Blade Patterns===
 
There are multiple ways of creating patterns on a blade. One method would be to weld two pattern sheets of steel together. This could be done with or without a sheet of iron in the middle depending on the forge.<ref>Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.</ref> Other methods include the use of Damascus steel and pattern welding. The Original method for creating Damascus steel was lost sometime in 1750. There have been some attempts to replicate it but non have been entirely successful.<ref>Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.</ref> The loss could have been from a lack of Wootz, the ore used to make the sword and found only in India, or a change in technique in an attempt to keep up with high demands. Pattern welding requires stacking alternating layers of iron or low carbon steel and high carbon steel or alternating steels of different grain size. The sheets are then curryed, or welded together. They can then be folded bent and twisted during forging to create different patterns.<ref>Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.</ref>
 
There are multiple ways of creating patterns on a blade. One method would be to weld two pattern sheets of steel together. This could be done with or without a sheet of iron in the middle depending on the forge.<ref>Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.</ref> Other methods include the use of Damascus steel and pattern welding. The Original method for creating Damascus steel was lost sometime in 1750. There have been some attempts to replicate it but non have been entirely successful.<ref>Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.</ref> The loss could have been from a lack of Wootz, the ore used to make the sword and found only in India, or a change in technique in an attempt to keep up with high demands. Pattern welding requires stacking alternating layers of iron or low carbon steel and high carbon steel or alternating steels of different grain size. The sheets are then curryed, or welded together. They can then be folded bent and twisted during forging to create different patterns.<ref>Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.</ref>
 +
<gallery mode="packed">
 +
Image:Two Decorated Plates.PNG|''Sword With two decorated plates Welded together<ref>Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.</ref>''
 +
Image:Twisted Bars.PNG|''Carolingian sword: The pattern was obtained by welding two bars twisted in opposite directions<ref>Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.</ref>''
 +
Image:Stacked Plates.PNG|''Undated Merovingian sword: The pattern was created by stacking steel plates of different grain sizes, then welding and folding them<ref>Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.</ref>''
 +
</gallery>
 
<br><br>
 
<br><br>
  
 
===Inscriptions===
 
===Inscriptions===
 +
{{Infobox
 +
|title = Medieval sword hilt
 +
|bodystyle = width:25em
 +
|image = [[File:Albion Baron Medieval Sword 2 (6092403878).jpg|320px|alt=Image ]]
 +
|caption = Note the Cross symbol on the pommel
 +
|label2 = '''Artist'''
 +
|data2 = Attributed to Søren Niedziella<ref> By Søren Niedziella from Denmark (Albion_Baron_Medieval_Sword_2) [CC BY 2.0 (http://creativecommons.org/licenses/by/2.0)], via Wikimedia Commons</ref>
 +
}}
 +
<br>
 
Inlays were made by Carving out the desired design in the blade with a chisel. Gold or other metal thread was place over the carvings then hammered in. It was hammered in using a lager flat hammer that would be place on the sword then hit with a more standard hammer.<ref>Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.</ref>
 
Inlays were made by Carving out the desired design in the blade with a chisel. Gold or other metal thread was place over the carvings then hammered in. It was hammered in using a lager flat hammer that would be place on the sword then hit with a more standard hammer.<ref>Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.</ref>
 
<br><br>
 
<br><br>
Line 53: Line 91:
 
=Section 2: Deliverable=
 
=Section 2: Deliverable=
 
<br>
 
<br>
[[File: ProjectPicture.jpg|x320px|right|thumb| Additional Image]]<br>
+
For the Deliverable, I created a sword using some medieval sword forging techniques, such as drawing and cornering. By Comparing my Sword to those in ''The Illustrated Directory of Swords & Sabres'' by Harvey J. S. Withers, my sword is most like a European knightly sword from c.1350. Since creating art on a sword takes a more skilled blacksmith I decided to simple forge a sword to get an idea of how difficult creating the art along with the sword must have been. The Sword was made at a four-day workshop offered by the Forge of Avalon on Glastonbury. The class was taught by Richard, the owner of the forge. In order to participate in the class, we needed safety glasses, heat resistant work gloves (not welding gauntlets), nonflammable clothes, and sturdy shoes. The next section will go into how the sword was made.
For the Deliverable, I created a sword using some medieval sword forging techniques, such as drawing and cornering. By Comparing my Sword to those in ''The Illustrated Directory of Swords & Sabres'' by Harvey J. S. Withers, my sword is most like a European knightly sword from c.1350. Since creating art on a sword takes a more skilled blacksmith I decided to simple forge a sword to get an idea of how difficult creating the art along with the sword must have been. The Sword was made at a four day workshop offered by the Forge of Avalon on Glastonbury. The class was taught by Richard, the owner of the forge. In order to participate in the class we needed safety glasses, heat resistant work gloves (not welding gauntlets), non flammable clothes, and sturdy shoes.  
+
<gallery mode="packed">
 +
Image:European Knightly Sword.JPG|''European Knightly Sword c.1350<ref>Withers , %. J. (2011). The Illustrated Directory of Swords & Sabres. Southwater.</ref>''
 +
</gallery>
 
<br><br>
 
<br><br>
 
==Process of sword forging==
 
==Process of sword forging==
 
<br>
 
<br>
We started by forging nails to learn basic skills such are making points, drawing, cornering, and making heads. Cornering is done by heating the metal then hammering at the end of the piece with a slight angle and rotating the piece at 90 degree angles to create a square point ant the end. Drawing involves heating again and hammering the piece while slowing moving the piece away from the direction you want to draw it under the hammer. Drawing lengthens and narrows the piece. Cornering it done by heating and hammering in line with the side of the anvil in order to create a corner in between sections of a piece. To create the head of the nail, We cut the nail off by heating it and hammering it over the hardy then snapping it off in the heading tool. before snapping the nail off the rod that its being forged out of it is important to make sure the head is hot enough because the heading tool sucks heat out of the nail and you need enough time to hammer out the head. Once the nail in the heading tool you place the nail in the hardy hole and hammer where the cut was in order to create a flat head. <br>
+
===Learning the Basics===
 +
We started by forging nails to learn basic skills such are making points, drawing, cornering, and making heads. Cornering is done by heating the metal then hammering at the end of the piece with a slight angle and rotating the piece at 90 degree angles to create a square point at the end. Drawing involves heating again and hammering the piece while slowing moving the piece away from the direction you want to draw it under the hammer. Drawing lengthens and narrows the piece. Cornering it done by heating and hammering in line with the side of the anvil in order to create a corner in between sections of a piece. To create the head of the nail, we cut the nail off by heating it and hammering it over the hardy then snapping it off in the heading tool. before snapping the nail off the rod that its being forged out of it is important to make sure the head is hot enough because the heading tool sucks heat out of the nail and you need enough time to hammer out the head. Once the nail in the heading tool you place the nail in the hardy hole and hammer where the cut was in order to create a flat head. <br>
 
<gallery mode="packed">
 
<gallery mode="packed">
 
Image:Anvil 2.JPG|''Anvil''
 
Image:Anvil 2.JPG|''Anvil''
Line 71: Line 112:
 
Image:Nails.JPG|''Nails I created''
 
Image:Nails.JPG|''Nails I created''
 
</gallery>
 
</gallery>
Work on the sword started with it cross guard. We stared with a square rod of low carbon steel (less than 1% carbon) and marked out a 80mm section a 30mm section and another 80mm section. We then drew one of the 80mm sections. We cut at the end of the other 80mm section the same way we cut the nails off their rods. We then drew out the other 80mm section. We used calipers to find the center of the piece after we drew it and marked the center. We then heated it and used a chisel to create the slot for the blade in the center if the guard. We had to use to different kinds of chisel to get the right shaped hole.
+
===Cross Guard===
<br>
+
Work on the sword started with it cross guard. We stared with a square rod of low carbon steel (less than 1% carbon) and marked out an 80mm section, a 30mm section, and another 80mm section. We then drew one of the 80mm sections. We cut at the end of the other 80mm section the same way we cut the nails off their rods. We then drew out the other 80mm section. We used calipers to find the center of the piece after we drew it and marked the center. We then heated it and used a chisel to create the slot for the blade in the center if the guard. We had to use to different kinds of chisel to get the right shaped hole.
The blade was created next. We started with some flat rod cut at a 45 degree angle of high carbon steel (about 7% carbon). We created points on both ends by heating them and hammering the 45 degree angles down. Once the point were shaped we chose our favorite one to became the point of the blade. we then drew that end of the blade out so it would have a taper.To create the tang, we marked a point 140 mm away from the end of the blade then Richard used a spring loaded press in order to corner the section of the tang that would fit into the cross guard. The spring loaded press was also used to draw out blade out more. we then marked about 3/4 of an inch up from our mark and drew out the section after that by hand. the spring loaded press was used again in order to further draw that section out and corner it again. We had to round the last section of the blade by hand. We also had to add a bevel to the edges of the blade. this was done by hammering at an angle until the end fit in the sizing tool. Through all these steps we had to brush the blade with a wire brush to keep oxidized chunks of steel called hammer scales from getting pounded into the blade
+
<br><br>
 +
===Blade===
 +
The blade was created next. We started with some flat rod cut at a 45-degree angle of high carbon steel (about 7% carbon). We created points on both ends by heating them and hammering the 45 degree angles down. Once the point was shaped we chose our favorite one to became the point of the blade. we then drew that end of the blade out so it would have a taper. To create the tang, we marked a point 140 mm away from the end of the blade then Richard used a spring loaded press in order to corner the section of the tang that would fit into the cross guard. The spring loaded press was also used to draw out blade out more. we then marked about 3/4 of an inch up from our mark and drew out the section after that by hand. the spring loaded press was used again in order to further draw that section out and corner it again. We had to round the last section of the blade by hand. We also had to add a bevel to the edges of the blade. this was done by hammering at an angle until the end fit in the sizing tool. Through all these steps we had to brush the blade with a wire brush to keep oxidized chunks of steel called hammer scales from getting pounded into the blade
 
<br>
 
<br>
 +
<gallery mode="packed">
 +
Image:Brushing Hammer Scales.JPG|''Brushing off Hammer Scales''
 +
Image:Shaping the Point.JPG|''Turning the 45 degree angle into a point''
 +
Image:Step 1.JPG|''Blade with two points. One end drawn to be the point of the blade''
 +
Image:Adding the Taper.JPG|''Adding the taper''
 +
Image:Step 2.JPG|''Narrowed end to become the tang''
 +
Image:Step 3.JPG|''Blade with completed tang and bevel''
 +
</gallery>
 +
===Pommel===
 
Next we started work on the pommel. We started with a round chunk of rod and heated it. We had to pound off and cutting marks and oxidants. We then rounded the corners of the rod. the final step was using a special tool and a hammer to create a circle in the middle of the pommel. Brushing was required for this piece too. We used a drill press in order to make a hole for the tang to go through. we then heated one end of the pommel and used a chisel to give one hole a rectangular dent so the pommel would not rotate on the blade.  
 
Next we started work on the pommel. We started with a round chunk of rod and heated it. We had to pound off and cutting marks and oxidants. We then rounded the corners of the rod. the final step was using a special tool and a hammer to create a circle in the middle of the pommel. Brushing was required for this piece too. We used a drill press in order to make a hole for the tang to go through. we then heated one end of the pommel and used a chisel to give one hole a rectangular dent so the pommel would not rotate on the blade.  
 
<br>  
 
<br>  
 +
<gallery mode="packed">
 +
Image:Cut removal.JPG|''Removing the cut marks and oxidants''
 +
Image:Adding Circle.JPG|''Adding the center circle''
 +
</gallery>
 +
===Assembly===
 
Hammer scales where removed from all the pieces using a variety of sanders and a special hammer was used to dig them out of the blade. The Pommel was then test fitted to the tang and extra material was cut off of the tang. The cut was made about 1/2 inch from where the pommel ended. The blade was grinded down using a belt sander to give it a nice finish. The blade, cross guard and pommel were them assembled and the rivet to hole the pommel on was made by heating the end of the tang with a blow torch and hammering down the 1/2 inch of material that was left before. We then tightened the cross guard by hitting it with a hammer.  
 
Hammer scales where removed from all the pieces using a variety of sanders and a special hammer was used to dig them out of the blade. The Pommel was then test fitted to the tang and extra material was cut off of the tang. The cut was made about 1/2 inch from where the pommel ended. The blade was grinded down using a belt sander to give it a nice finish. The blade, cross guard and pommel were them assembled and the rivet to hole the pommel on was made by heating the end of the tang with a blow torch and hammering down the 1/2 inch of material that was left before. We then tightened the cross guard by hitting it with a hammer.  
 
<br>
 
<br>
 +
<gallery mode="packed">
 +
Image:Completed Parts.JPG|''Completed Parts''
 +
Image:Groups Swords.JPG|''Classes swords before the handles''
 +
</gallery>
 +
 +
===Handle===
 
The last step was making the handle. This was done by measuring the exposed bit of the tang and cutting two bits of wood to fit that section. A slot was made for the tang in each piece by marking the wood then cutting it with a box cutter and a chisel. The wood was then sanded to create a handle shape and glued to the tang. We then glue leather over the wood and that concluded the sword making.  
 
The last step was making the handle. This was done by measuring the exposed bit of the tang and cutting two bits of wood to fit that section. A slot was made for the tang in each piece by marking the wood then cutting it with a box cutter and a chisel. The wood was then sanded to create a handle shape and glued to the tang. We then glue leather over the wood and that concluded the sword making.  
 +
<br>
 +
<gallery mode="packed">
 +
Image:Finished Sword.JPG|''Finished Sword''
 +
</gallery>
 
<br><br>
 
<br><br>
  
 
==Results==
 
==Results==
<br><br>
+
<br>
===Gallery===
+
Forging the sword was difficult even with the help of modern technology. There are a lot of imperfections in the blade due to hammer scales getting pounded into the metal despite the brushing and the decorative circle in the pommel is slightly off center. Otherwise it is a functional sword.  
<gallery mode="packed">
 
Image:Syllabus.jpg|''Caption 1''
 
Image:ProjectPicture.jpg|''Caption 2''
 
Image:Bigben.jpg|''Caption 3''
 
Image:Yourprofilepicture.jpg|''Caption 4''
 
</gallery>
 
 
<br><br>
 
<br><br>
  

Latest revision as of 08:15, 23 June 2017

Art in Medieval Sword Forging

by Nicole Petilli

Art in Medieval Sword Forging
Cool Sword Pic
Deliverable Sword
Location Forge of Avalon, Glastonbury

Abstract

The purpose of this project was to study how art was involved in medieval sword making and create a medieval sword. I have never done any kind of forging previously. I found that most art in medieval swords are religious in nature and meant to give the wielder divine favor in battle. A lot is not known about inscriptions because of a lack of understanding in Latin abbreviations and grammar. Sword blades could also be decorated with wave patterns during forging. I created a sword in order to understand the processes that would have been involved in creating the art. I was unable to actually create any art in my sword due to a lack of skill.



Introduction


The aim of this project was to find how art factored into the making of medieval swords in Europe. The most common kind of inscription are religious invocations. Blades were commonly decorated with religious symbols in order to give the wielder divine favor in battle. Other inscriptions could have been meant to give the blades magical power. Names could also be found on different blades along with maker's marks. A lot of the lettering cannot be interpreted due to a lack of understanding in Latin abbreviations and grammar. Other combinations might also be a magical language or random letters meant to give the blade a magical look. Inscriptions where created using a chisel. They could be filled n by hammering metal treads into the material once it had been carved. Patterning was also common as smiths aimed to recreate Damascus steel which was legendary for its strength and flexibility. Pattern welding became common to create different wave patters similar to Damascus steel in the blades. Making a sword takes a lot of skill. I tried to get an idea for this by making my own sword.

Section 1: Background

Time Period


I am defining a Medieval sword to mean any sword crafted in Europe between 500 and 1400 AD. During this time period, swords would be mainly used for fighting as seen by the fact that the shape of the blade depends on the fighting style native to that area. They also would have be used in the Crusades.[1] The majority of swords where made to be functional as opposed to be artistic. The swords did have art on them designed to be functional in the forms of engravings meant to give the blades magical power or blessings from various deities.[2] Designs in the blades did come about from trying to mimic Damascus steel, steel made from wootz, an iron ore from India, and crafted in Damascus, a trade center from that time period, because of its highly functional qualities.[3] For the most part the swords were not very decorated.

Meaning of Art in Swords


Blade Patterns

Damascus Steel Knife
Image
Damascus Steel has a distinctive wave pattern
Artist Attributed to Rich Bowen[4]


Damascus steel swords were very popular during the medieval period due to their combination of strength and flexibility. Using Damascus steel causes a water ripple looking pattern in the blade. For this reason, many smiths found ways to copy the pattern despite not having the steel. The patterning was entirely for aesthetic uses and had no real meaning beyond the implication that it was a high quality sword which may or may not have been true depending on whether or not it was Damascus steel and if it was forged properly.[5]

Inscriptions

Blade with Inscriptions
Image
The meaning of many inscriptions are unknown
Artist Photographed by: York Museums Trust Staff[6]


Inscriptions on Medieval swords are very common and severed a variety of purposes. There are four kinds of inscriptions that are found on medieval swords, runic inscriptions, symbols, religious vocations, and periodic sequences.[7] Runic inscriptions were frequently maker's marks, which show who forged the sword, but also could have been the names of the owners, makers (their name being different form their mark), donators, carriers or the weapons name. Having a name was rare and was likely used for gifting swords. They could have also been to remind the barer to show bravery or been written by sorceresses to give the blade magic power.[8][9] Religious vocations would have been meant to give the wielders divine favor in battle.[10] Symbols and ornaments were likely religious.[11] Most writing on medieval swords have religious, magical, or other protective meaning.[12][13] Among more common letter sequences such as SDX, which means Sanctus Dominus Christus or Holy Lord Christ, SD(I)X, which could have meant salvator Dominus Iesus Xrist or Liberator Lord Jesus Christ, and ULFBERTH which were mass produced. There are different sequences that do not appear to have any meaning.[14] This could be because hey are Latin abbreviations of songs or verse that are unknown or due to a lack of understanding the grammar. Because witting was very uncommon at the time, any kind of lettering would have a magical connotation. Some of the inscriptions could have been nonsense meant to be a magical language.[15]

Metropolitan Museum of Art's c.1400 Sword

This is one of the very few cases where the inscription on a sword is not a religious invocation. The script on the pommel reads "here, too virtue has its due reward" and the script on the blade is mostly illegible. It could be the only surviving sword with a presentation inscription from the 14th century.[16]



Making The Art


Blade Patterns

There are multiple ways of creating patterns on a blade. One method would be to weld two pattern sheets of steel together. This could be done with or without a sheet of iron in the middle depending on the forge.[21] Other methods include the use of Damascus steel and pattern welding. The Original method for creating Damascus steel was lost sometime in 1750. There have been some attempts to replicate it but non have been entirely successful.[22] The loss could have been from a lack of Wootz, the ore used to make the sword and found only in India, or a change in technique in an attempt to keep up with high demands. Pattern welding requires stacking alternating layers of iron or low carbon steel and high carbon steel or alternating steels of different grain size. The sheets are then curryed, or welded together. They can then be folded bent and twisted during forging to create different patterns.[23]



Inscriptions

Medieval sword hilt
Image
Note the Cross symbol on the pommel
Artist Attributed to Søren Niedziella[27]


Inlays were made by Carving out the desired design in the blade with a chisel. Gold or other metal thread was place over the carvings then hammered in. It was hammered in using a lager flat hammer that would be place on the sword then hit with a more standard hammer.[28]

Section 2: Deliverable


For the Deliverable, I created a sword using some medieval sword forging techniques, such as drawing and cornering. By Comparing my Sword to those in The Illustrated Directory of Swords & Sabres by Harvey J. S. Withers, my sword is most like a European knightly sword from c.1350. Since creating art on a sword takes a more skilled blacksmith I decided to simple forge a sword to get an idea of how difficult creating the art along with the sword must have been. The Sword was made at a four-day workshop offered by the Forge of Avalon on Glastonbury. The class was taught by Richard, the owner of the forge. In order to participate in the class, we needed safety glasses, heat resistant work gloves (not welding gauntlets), nonflammable clothes, and sturdy shoes. The next section will go into how the sword was made.



Process of sword forging


Learning the Basics

We started by forging nails to learn basic skills such are making points, drawing, cornering, and making heads. Cornering is done by heating the metal then hammering at the end of the piece with a slight angle and rotating the piece at 90 degree angles to create a square point at the end. Drawing involves heating again and hammering the piece while slowing moving the piece away from the direction you want to draw it under the hammer. Drawing lengthens and narrows the piece. Cornering it done by heating and hammering in line with the side of the anvil in order to create a corner in between sections of a piece. To create the head of the nail, we cut the nail off by heating it and hammering it over the hardy then snapping it off in the heading tool. before snapping the nail off the rod that its being forged out of it is important to make sure the head is hot enough because the heading tool sucks heat out of the nail and you need enough time to hammer out the head. Once the nail in the heading tool you place the nail in the hardy hole and hammer where the cut was in order to create a flat head.

Cross Guard

Work on the sword started with it cross guard. We stared with a square rod of low carbon steel (less than 1% carbon) and marked out an 80mm section, a 30mm section, and another 80mm section. We then drew one of the 80mm sections. We cut at the end of the other 80mm section the same way we cut the nails off their rods. We then drew out the other 80mm section. We used calipers to find the center of the piece after we drew it and marked the center. We then heated it and used a chisel to create the slot for the blade in the center if the guard. We had to use to different kinds of chisel to get the right shaped hole.

Blade

The blade was created next. We started with some flat rod cut at a 45-degree angle of high carbon steel (about 7% carbon). We created points on both ends by heating them and hammering the 45 degree angles down. Once the point was shaped we chose our favorite one to became the point of the blade. we then drew that end of the blade out so it would have a taper. To create the tang, we marked a point 140 mm away from the end of the blade then Richard used a spring loaded press in order to corner the section of the tang that would fit into the cross guard. The spring loaded press was also used to draw out blade out more. we then marked about 3/4 of an inch up from our mark and drew out the section after that by hand. the spring loaded press was used again in order to further draw that section out and corner it again. We had to round the last section of the blade by hand. We also had to add a bevel to the edges of the blade. this was done by hammering at an angle until the end fit in the sizing tool. Through all these steps we had to brush the blade with a wire brush to keep oxidized chunks of steel called hammer scales from getting pounded into the blade

Pommel

Next we started work on the pommel. We started with a round chunk of rod and heated it. We had to pound off and cutting marks and oxidants. We then rounded the corners of the rod. the final step was using a special tool and a hammer to create a circle in the middle of the pommel. Brushing was required for this piece too. We used a drill press in order to make a hole for the tang to go through. we then heated one end of the pommel and used a chisel to give one hole a rectangular dent so the pommel would not rotate on the blade.

Assembly

Hammer scales where removed from all the pieces using a variety of sanders and a special hammer was used to dig them out of the blade. The Pommel was then test fitted to the tang and extra material was cut off of the tang. The cut was made about 1/2 inch from where the pommel ended. The blade was grinded down using a belt sander to give it a nice finish. The blade, cross guard and pommel were them assembled and the rivet to hole the pommel on was made by heating the end of the tang with a blow torch and hammering down the 1/2 inch of material that was left before. We then tightened the cross guard by hitting it with a hammer.

Handle

The last step was making the handle. This was done by measuring the exposed bit of the tang and cutting two bits of wood to fit that section. A slot was made for the tang in each piece by marking the wood then cutting it with a box cutter and a chisel. The wood was then sanded to create a handle shape and glued to the tang. We then glue leather over the wood and that concluded the sword making.



Results


Forging the sword was difficult even with the help of modern technology. There are a lot of imperfections in the blade due to hammer scales getting pounded into the metal despite the brushing and the decorative circle in the pommel is slightly off center. Otherwise it is a functional sword.

Conclusion


The main function of art in medieval swords was to give the sword power via divine favor or magic. Swords we also had makers marks in order to tell who made it. They could also have names or reminders to be brave in battle written on them. Smith's also tried to replicate Damascus steel. Damascus steel was sought after due to legendary hardness and flexibility and created a distinctive wave pattern in the blade. Pattern welded steels became common. They were made by alternating layers of low and high carbon steel then twisting and folding them while forging to get various patterns. Patterning in the blade was mainly for decorative purposes. Making a sword is very difficult even with modern day machines such as belt sanders, spring loaded presses, ban saws, and drill presses. Smiths would have needed a great amount of skill to forge swords with decoration. A Future area of study could be in the History of Damascus steels and how they shaped sword forging past the medieval time period.

External Links

Forge of Avalon Website: http://www.forgeofavalon.com/index2.php

References

  1. Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.
  2. Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132
  3. Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.
  4. Attributed to Rich Bowen from Lexington, KY, USA (Damascus steel hunting knife) [CC BY 2.0 (http://creativecommons.org/licenses/by/2.0)], via Wikimedia Commons
  5. Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.
  6. Photographed by: York Museums Trust Staff [CC BY-SA 4.0 (http://creativecommons.org/licenses/by-sa/4.0)], via Wikimedia Commons
  7. Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132
  8. Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132
  9. Nickel, H. (1969). A Knightly Sword with Presentation Inscriptions. Metropolitan Museum Journal, 2, 209-210. doi:10.2307/1512593
  10. Nickel, H. (1969). A Knightly Sword with Presentation Inscriptions. Metropolitan Museum Journal, 2, 209-210. doi:10.2307/1512593
  11. Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132
  12. Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132
  13. Nickel, H. (1969). A Knightly Sword with Presentation Inscriptions. Metropolitan Museum Journal, 2, 209-210. doi:10.2307/1512593
  14. Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132
  15. Worley, J., Wagner, T. (2013) How to make swords talk: an interdisciplinary approach to understanding medieval swords and their inscriptions. Waffen- und Kostümkunde, 55(2): 113-132
  16. Nickel, H. (1969). A Knightly Sword with Presentation Inscriptions. Metropolitan Museum Journal, 2, 209-210. doi:10.2307/1512593
  17. Nickel, H. (1969). A Knightly Sword with Presentation Inscriptions. Metropolitan Museum Journal, 2, 209-210. doi:10.2307/1512593
  18. Nickel, H. (1969). A Knightly Sword with Presentation Inscriptions. Metropolitan Museum Journal, 2, 209-210. doi:10.2307/1512593
  19. Nickel, H. (1969). A Knightly Sword with Presentation Inscriptions. Metropolitan Museum Journal, 2, 209-210. doi:10.2307/1512593
  20. Nickel, H. (1969). A Knightly Sword with Presentation Inscriptions. Metropolitan Museum Journal, 2, 209-210. doi:10.2307/1512593
  21. Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.
  22. Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.
  23. Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.
  24. Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.
  25. Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.
  26. Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.
  27. By Søren Niedziella from Denmark (Albion_Baron_Medieval_Sword_2) [CC BY 2.0 (http://creativecommons.org/licenses/by/2.0)], via Wikimedia Commons
  28. Durand-Charre, M. (2014). Damascus and pattern-welded steels forging blades since the iron age. Les Ulis (Essonne): EDP sciences.
  29. Withers , %. J. (2011). The Illustrated Directory of Swords & Sabres. Southwater.